E-mail Received, 9 March 2023
Link 110 and others

Alan Bird writes:-
May I say firstly how much I enjoy looking at the pages of your Museum of the Broadcast Television Camera. I always seem to find something new and intriguing there!
A bit about myself – having always been interested in TV cameras since a teenager, I built a flying spot scanner when aged about 15, primarily for 35mm slides, using an old TV chassis for the scanner, a slide projector in reverse and a 931A photomultiplier for the business end. I even used it for live scanning, with quite reasonable results! A NEV vidicon camera followed when I received my amateur licence G6AAQ/T a year or so later. Obviously, after school the BBC was a next step and I joined as a Technical Assistant in 1963, and was posted to Television News Alexandra Palace after training. Loved it!
At A.P. we had EMI 201 vidicons which were manned in Studio A and remote-controlled in Studio B, a fixed Peto-Scott in the Newsroom (405 only! Later replaced with a Marconi Drainpipe) and Marconi Mk. 3s on the OB unit. I’m pretty sure a Mk.3 was used as a standards converter as well. The EMI 201s in Studio A were replaced with three Marconi Mk.7s which were redeployed from TVC. I then worked for a time in TK, which operated two Pye Mk.8 telecines.
Then I went to be Vision Engineer at Portland Place News TV Studio in basement of BH, with two manned EMI 201s and one remote controlled. We also had responsibility for College Mews, which was a remote-controlled studio in Parliament, and the Press Room at London Heathrow Airport, with two Pye Mk.3s which I believe were the last 3in. Image Orthicons the BBC used – but I may be wrong. On a quiet weekend it was pleasant to visit the airport, swich on and see if anything worked.
When the studio at Portland Place was colourised with two EMI 2001s, (the remote-controlled 201 was retained for captions, I think) we decamped during the installation down to the sub-basement to Studio S.1, where we operated with two Pye Mk.6s from an old MCR. After colourisation I was promoted to Studio Engineer back to AP with the Open University Production Centre. Back to Orthicons, this time with four Pye Mk.5s in Studio A which were ex-Riverside. Then we got hold of an old OB van, MCR28, with its complement of Pye Mk.6s.
Colourisation took place – first with a new OB van, then the studio. Once again we operated with a derig while the studio was being upgraded. We used Studio B and had Pye Mk.6s and a derig kit from MCR24. Then shock horror – a move from valves and I.O.s to CMOS chips and 25mm. plumbicons with ACT and bias light overnight, without even going through a transistor phase! Even TVC didn’t have these tubes yet! So no wisdom to be had from there. No handbooks from the manufacturer either, just a box of circuit diagrams which might or might not bear any relationship to the actual equipment. We found out the hard way that 15 volt working tantalum capacitors were at their limit with a 12 volt rail and pungent smoke signals indicated a premature demise. It wasn’t always easy swapping out a duff board either as the replacement was sometimes a different physical size. The old I.O.s might have been heavy, but they were robust – which the 110s certainly were not, particularly when used on OBs
We had a complement of nine Link 110s – three on the OB (S/No. 4, 5 and 6 which were pretty much hand-built and showed it), four in the studio (S/Nos. 7-10), an Episcope S/No. 11 (vertically-mounted X-Y plotter over a table for graphics, made by Evershed Power Optics), and S/No. 12 was our maintenance channel. I can recollect the serial numbers well, the number of times I had to write them in the maintenance log. All had RTH Varotal 30 lenses, and the OB also had an optional Schneider 30:1 as well. It was always intended that the OB would have portable cameras, and the two earliest 110s (4 and 5) were replaced by Link 120s about 1978. Whether ‘portable’ fits the description of the 120 I have my doubts…but then we got an Ikegami HL-79D which was quite an eye-opener!
Then we moved to new studio centre built at Milton Keynes. Initially we used the 110s in the studio, and the OB moved to single camera use with Ikegami HL-79Ds in estate cars and a ‘combining unit’ in a VW van if we needed multi camera operation. The studio 110s became more and more unreliable, and were replaced by Link 125s with Schneider 15:1 lenses. I moved through being Senior Television Engineer Studios, then Technical Services manager and finally Assistant Head of Engineering and Operations at OUPC. This was so much more of an office job, and it was on the cards that studio operations were going to cease so I managed to make myself redundant and become a Baptist minister at 45.
Sorry for all this rambling, but I thought I would get details down before senility takes its toll. I hope that the details and serial numbers might add something to your information the cameras, both old and new that we used at OUPC – a little BBC operation that quite often gets overlooked. Please feel free to use any details in your write-ups.
As a PS, I believe that Link 110s were also used in a Cardiff OB unit, but can’t tell you anything about them.
Regards